Edit | Breakpoints

Click Breakpoints on the Edit menu to display or control breakpoints.

This command is equivalent to pressing ALT+F9. If a Source window or the Disassembly window is not active, you can also press F9 or click the Insert or remove breakpoint (F9) button (Screen shot of the Insert or remove breakpoint button) on the toolbar.

However, if a Source window or the Disassembly window is open, the Insert or remove breakpoint (F9) button and the F9 key set a breakpoint on the current line. (If there is already a breakpoint set at the current line, this button or key will remove the breakpoint.)

If a statement or call spans multiple lines, WinDbg sets the breakpoint on the last line of the statement or call. You should insert the caret (^) on or before the statement to set a breakpoint for the whole statement. If the debugger cannot set a breakpoint at the current caret position, it will search in a downward direction for the next allowed position and insert the breakpoint there.

Dialog Box

When you click Breakpoints, the Breakpoints dialog box appears. This dialog box displays all current breakpoint information and is presented in the following columns:

  • The breakpoint number. This number is a decimal number that you can use to refer to the breakpoint in future commands.

  • The breakpoint status. This status can be e (enabled) or d (disabled).

  • (Unresolved breakpoints only) The letter u. This letter appears if the breakpoint is unresolved (that is, it does not match any currently-loaded module address). For details, see Unresolved Breakpoints (bu Breakpoints).

  • The virtual address of the breakpoint. If you have enabled the loading of source line numbers, the display includes file and line number information instead of address offsets. If the breakpoint is unresolved, the address appears at the end of the listing instead of here.

  • (Processor breakpoints only) Type and size information. This information can be e (execute), r (read/write), w (write), or i (input/output). These types are followed with the size of the block, in bytes. For details, see Processor Breakpoints (ba Breakpoints).

  • The number of passes that are remaining until the breakpoint becomes active, followed by the initial number of passes in parentheses. The number of times that the program counter passes through the breakpoint without breaking is one less than the value of this number. Therefore, this number is never lower than 1. Note also that this number counts only the times the application executes through this point. In other words, stepping over this point does not count. After the full count has been reached, you can reset the count only by clearing and resetting the breakpoint.

  • The associated process and thread. If thread is given with three asterisks (***), this breakpoint is not a thread-specific breakpoint.

  • The module and function, with offset, that correspond to the breakpoint address. If the breakpoint is unresolved, the breakpoint address appears here, in parentheses. If the breakpoint is set on a valid address but symbol information is missing, this column will be blank.

  • The command string that is automatically executed when this breakpoint is hit. This command string is displayed in quotation marks. If the breakpoint is hit, the commands in this command string are executed until application execution resumes. Any command that resumes program execution (such as g or t) will stop the execution of the command list.

If you select any breakpoint, you can then click the Remove, Disable, or Enable button. The Remove button permanently removes the breakpoint. The Disable button temporarily deactivates the breakpoint. The Enable button re-enables a disabled breakpoint.

The Remove All button permanently removes all breakpoints.

You can also enter commands in the Command box in the following ways:

When you are entering a new breakpoint, you can also do the following:

  • Create a thread-specific breakpoint by entering a thread specifier in the Thread box. Do not include the tilde (~) character that is typically prefixed to a thread specifier.

  • Create a conditional breakpoint by entering a condition in the Condition box. The condition can be any evaluable expression, and it will be evaluated according to the current expression syntax (see Evaluating Expressions). For more information about these types of breakpoints, see Setting a Conditional Breakpoint.

Additional Information

For more information about how to use breakpoints, other breakpoint commands and methods of controlling breakpoints, and setting breakpoints in user space from a kernel debugger, see Using Breakpoints. For more information about conditional breakpoints, see Setting a Conditional Breakpoint.

 

 

Send comments about this topic to Microsoft

Show: