Socket.SendTo Method (Byte(), Int32, Int32, SocketFlags, EndPoint)
Sends the specified number of bytes of data to the specified endpoint, starting at the specified location in the buffer, and using the specified SocketFlags.
Assembly: System (in System.dll)
Public Function SendTo ( buffer As Byte(), offset As Integer, size As Integer, socketFlags As SocketFlags, remoteEP As EndPoint ) As Integer
The position in the data buffer at which to begin sending data.
The number of bytes to send.
Return ValueType: System.Int32
The number of bytes sent.
buffer is null.
remoteEP is null.
offset is less than 0.
offset is greater than the length of buffer.
size is less than 0.
size is greater than the length of buffer minus the value of the offset parameter.
socketFlags is not a valid combination of values.
An operating system error occurs while accessing the Socket. See the Remarks section for more information.
The Socket has been closed.
A caller in the call stack does not have the required permissions.
In this overload, if you specify the DontRoute flag as the socketflags parameter, the data you are sending will not be routed.
If you are using a connectionless protocol, you do not need to establish a default remote host with the Connect method prior to calling . You only need to do this if you intend to call the Send method. If you do call the Connect method prior to calling , the remoteEP parameter will override the specified default remote host for that send operation only. You are also not required to call the Bind method, because the underlying service provider will assign the most appropriate local network address and port number. If you need to identify the assigned local network address and port number, you can use the LocalEndPoint property after the method successfully completes.
Although intended for connectionless protocols, Connect method or accept an incoming connection request using the Accept method. If you do not establish or accept a remote host connection, will throw a SocketException. You can also establish a default remote host for a connectionless protocol prior to calling the method. In either of these cases, will ignore the remoteEP parameter and only send data to the connected or default remote host.also works with connection-oriented protocols. If you are using a connection-oriented protocol, you must first establish a remote host connection by calling the
Blocking sockets will block until the requested number of bytes are sent. Since a non-blocking Socket completes immediately, it might not send all of the bytes requested in a single operation. It is your applications responsibility to keep track of the number of bytes sent and to retry the operation until the application sends the requested number of bytes. There is also no guarantee that the data you send will appear on the network immediately. To increase network efficiency, the underlying system may delay transmission until a significant amount of out-going data is collected. A successful completion of the method means that the underlying system has had room to buffer your data for a network send.
If you are using a connectionless protocol in blocking mode, SetSocketOption method and set the socket option to SocketOptionName.Broadcast. You must also be sure that the size does not exceed the maximum packet size of the underlying service provider. If it does, the datagram will not be sent and will throw a SocketException.will block until the datagram is sent. If you want to send data to a broadcast address, you must first call the
If you receive a SocketException, use the SocketException.ErrorCode property to obtain the specific error code. After you have obtained this code, refer to the Windows Sockets version 2 API error code documentation in the MSDN library for a detailed description of the error.
This member outputs trace information when you enable network tracing in your application. For more information, see Network Tracing in the .NET Framework.
The following code example sends a connectionless datagram to the specified remote host. The offset, size, and SocketFlags are passed to the method.
Public Shared Sub SendTo4() Dim hostEntry As IPHostEntry = Dns.GetHostEntry(Dns.GetHostName()) Dim endPoint As New IPEndPoint(hostEntry.AddressList(0), 11000) Dim s As New Socket(endPoint.Address.AddressFamily, SocketType.Dgram, ProtocolType.Udp) Dim msg As Byte() = Encoding.ASCII.GetBytes("This is a test") Console.WriteLine("Sending data.") ' This call blocks. s.SendTo(msg, 0, msg.Length, SocketFlags.None, endPoint) s.Close() End Sub 'SendTo4
Available since 1.1