Was this page helpful?
Your feedback about this content is important. Let us know what you think.
Additional feedback?
1500 characters remaining
Export (0) Print
Expand All

Downloading the Boot Loader to the AMD DBAu1500 Development Board (Windows CE 5.0)

Windows CE 5.0
Send Feedback

If you are downloading the Windows CE boot loader to the AMD DBAu1500 Development Board for the first time, you can use the following procedure.

To download the Windows CE boot loader for the first time

  1. Verify that the AMD DBAu1500 Development Board is turned off.
  2. Switch the red SWAP_BOOT switch, S8, to the upper position.
  3. On the development workstation, configure the terminal emulation software to the settings shown in the following table.
    Bits per secondData bitsParityStop bitsFlow control
    1152008None1None
  4. Turn on the AMD DBAu1500 Development Board by pressing the power switch, S3.

    The Yamon ROM Monitor should run and you should see the following output on the terminal window:

    YAMON ROM Monitor, Revision 02.13DB1500.
    Copyright (c) 1999-2000 MIPS Technologies, Inc. - All Rights Reserved.
    
    For a list of available commands, type 'help'.
    
    Compilation time =            Oct  7 2002  13:33:30
    MAC address =                 00.50.c2.0c.20.5a
    Processor Company ID =        0x03
    Processor ID/revision =       0x02 / 0x00
    Endianness =                  Little
    CPU =                         396 MHz
    Flash memory size =           32 MByte
    SDRAM size =                  64 MByte
    First free SDRAM address =    0x8008aad4
    
    YAMON>
    
  5. Download the Eboot image into RAM on the AMD DBAu1500 Development Board by typing the following command at the YAMON> command prompt:
    load asc:
    

    The following output appears after you type this command:

    About to load asc://tty0
    Press Ctrl-C to break
    Start dump from terminal program
    
  6. Start the download process from the terminal emulator using the Boot.sre file from the Release directory. The following output appears after you type this command:
    Start = 0x83f80004, range = (0x83f80000,0x83f8b4eb), format = SREC
    YAMON>
    
  7. At the YAMON> command prompt, type the following command to erase flash memory:
    erase 9ec00000 40000
    

    The following output appears after you type this command:

    what...
    The following area will be erased:
    Start address = 0x1ec00000
    Size          = 0x00040000
    Confirm ? (y/n) y
    Erasing...Done
    YAMON>
    
  8. Copy the Eboot image into flash memory by typing the following command at the YAMON> command prompt:
    copy 83f80000 9ec00000 20000
    

    The following output appears after you type this command:

    Copying...Done
    YAMON>
    
    Note   To determine the correct size of the image copy, add 1 to the download result.
  9. Turn off the AMD DBAu1500 Development Board.
  10. Swap flash memory blocks by switching the red SWAP_BOOT switch, S8, to the lower position.
  11. Configure the terminal emulation software to the following settings:
    Bits per secondData bitsParityStop bitsFlow control
    384008None1None
  12. Turn on the AMD DBAu1500 Development Board and verify that you downloaded the Windows CE boot loader.

    For the format of the Windows CE boot loader message, see Windows CE Boot Loader Output for the AMD DBAu1500 Development Board.

  13. Set the Media Access Control (MAC) addresses for the Au1500 on-chip Ethernet controllers and change other boot loader parameters as required.
    Note   Save new configuration settings to flash memory.
  14. Turn on the AMD DBAu1500 Development Board and verify that the device does not use the broadcast MAC address.

See Also

How to Use the BSP for the AMD DBAu1500 Development Board | Downloading the Run-Time Image to the AMD DBAu1500 Development Board


Send Feedback on this topic to the authors

Feedback FAQs

© 2006 Microsoft Corporation. All rights reserved.


Show:
© 2015 Microsoft