Expand Minimize

WSARecvEx function

The WSARecvEx function receives data from a connected socket or a bound connectionless socket. The WSARecvEx function is similar to the recv function, except that the flags parameter is used only to return information. When a partial message is received while using datagram protocol, the MSG_PARTIAL bit is set in the flags parameter on return from the function.

Note  The WSARecvEx function is a Microsoft-specific extension to the Windows Sockets specification.

Syntax


int PASCAL FAR WSARecvEx(
  _In_     SOCKET s,
  _Out_    char *buf,
  _In_     int len,
  _Inout_  int *flags
);

Parameters

s [in]

A descriptor that identifies a connected socket.

buf [out]

A pointer to the buffer to receive the incoming data.

len [in]

The length, in bytes, of the buffer pointed to by the buf parameter.

flags [in, out]

An indicator specifying whether the message is fully or partially received for datagram sockets.

Return value

If no error occurs, WSARecvEx returns the number of bytes received. If the connection has been closed, it returns zero. Additionally, if a partial message was received, the MSG_PARTIAL bit is set in the flags parameter. If a complete message was received, MSG_PARTIAL is not set in flags

Otherwise, a value of SOCKET_ERROR is returned, and a specific error code can be retrieved by calling WSAGetLastError.

Important  For a stream oriented-transport protocol, MSG_PARTIAL is never set on return from WSARecvEx. This function behaves identically to the recv function for stream-transport protocols.

Error codeMeaning
WSAECONNABORTED

The virtual circuit was terminated due to a time-out or other failure. The application should close the socket as it is no longer usable.

WSAECONNRESET

The virtual circuit was reset by the remote side executing a hard or abortive close. The application should close the socket as it is no longer usable. On a UPD-datagram socket this error would indicate that a previous send operation resulted in an ICMP "Port Unreachable" message.

WSAEFAULT

The buf parameter is not completely contained in a valid part of the user address space.

WSAEINPROGRESS

A blocking Windows Sockets 1.1 call is in progress, or the service provider is still processing a callback function.

WSAEINTR

The (blocking) call was canceled by the WSACancelBlockingCall call.

WSAEINVAL

The socket has not been bound with bind, or an unknown flag was specified, or MSG_OOB was specified for a socket with SO_OOBINLINE enabled or (for byte stream sockets only) len was zero or negative.

WSAENETDOWN

The network subsystem has failed.

WSAENETRESET

For a connection-oriented socket, this error indicates that the connection has been broken due to keep-alive activity that detected a failure while the operation was in progress. For a datagram socket, this error indicates that the time to live has expired.

WSAENOTCONN

The socket is not connected.

WSAENOTSOCK

The descriptor is not a socket.

WSAEOPNOTSUPP

MSG_OOB was specified, but the socket is not stream-style such as type SOCK_STREAM, OOB data is not supported in the communication domain associated with this socket, or the socket is unidirectional and supports only send operations.

WSAESHUTDOWN

The socket has been shut down; it is not possible to use WSARecvEx on a socket after shutdown has been invoked with how set to SD_RECEIVE or SD_BOTH.

WSAETIMEDOUT

The connection has been dropped because of a network failure or because the peer system failed to respond.

WSAEWOULDBLOCK

The socket is marked as nonblocking and the receive operation would block.

WSANOTINITIALISED

A successful WSAStartup call must occur before using this function.

 

Remarks

The WSARecvEx function that is part of the Microsoft implementation of Windows Sockets 2 is similar to the more common recv function except that the flags parameter is used for a single specific purpose. The flags parameter is used to indicate whether a partial or complete message is received when a message-oriented protocol is being used.

The value pointed to by the flags parameter is ignored on input. So no flags can be passed to the WSARecvEx function to modify its behavior. The value pointed to by the flags parameter is set on output. This differs from the recv and WSARecv functions where the value pointed to by the flags parameter on input can modify the behavior of the function.

The WSARecvEx and recv functions behave identically for stream-oriented protocols.

The flags parameter accommodates two common situations in which a partial message will be received:

  • When the application's data buffer size is smaller than the message size and the message coincidentally arrives in two pieces.
  • When the message is rather large and must arrive in several pieces.

The MSG_PARTIAL bit is set in the value pointed to by the flags parameter on return from WSARecvEx when a partial message was received. If a complete message was received, MSG_PARTIAL is not set in the value pointed to by the flags parameter.

The recv function is different from the WSARecvEx and WSARecv functions in that the recv function always receives a single message for each call for message-oriented transport protocols. The recv function also does not have a means to indicate to the application that the data received is only a partial message. An application must build its own protocol for checking whether a message is partial or complete by checking for the error code WSAEMSGSIZE after each call to recv. When the application buffer is smaller than the data being sent, as much of the message as will fit is copied into the user's buffer and recv returns with the error code WSAEMSGSIZE. A subsequent call to recv will get the next part of the message.

Applications written for message-oriented transport protocols should be coded for this possibility if message sizing is not guaranteed by the application's data transfer protocol. An application can use recv and manage the protocol itself. Alternatively, an application can use WSARecvEx and check that the MSG_PARTIAL bit is set in the flags parameter.

The WSARecvEx function provides the developer with a more effective way of checking whether a message received is partial or complete when a very large message arrives incrementally. For example, if an application sends a one-megabyte message, the transport protocol must break up the message in order to send it over the physical network. It is theoretically possible for the transport protocol on the receiving side to buffer all the data in the message, but this would be quite expensive in terms of resources. Instead, WSARecvEx can be used, minimizing overhead and eliminating the need for an application-based protocol.

Note   All I/O initiated by a given thread is canceled when that thread exits. For overlapped sockets, pending asynchronous operations can fail if the thread is closed before the operations complete. See the ExitThread function for more information.

Requirements

Minimum supported client

Windows 2000 Professional [desktop apps only]

Minimum supported server

Windows 2000 Server [desktop apps only]

Header

Mswsock.h

Library

Mswsock.lib

DLL

Mswsock.dll

See also

Winsock Reference
Winsock Functions
recv
recvfrom
select
send
socket
WSAAsyncSelect
WSARecv

 

 

Community Additions

ADD
Show:
© 2014 Microsoft. All rights reserved.