Export (0) Print
Expand All

Depth Bias

Polygons that are coplanar in 3D space can be made to appear as if they are not coplanar by adding a z-bias (or depth bias) to each one. This is a technique commonly used to ensure that shadows in a scene are displayed properly. For instance, a shadow on a wall will likely have the same depth value as the wall. If an application renders a wall first and then a shadow, the shadow might not be visible, or depth artifacts might be visible.

An application can help ensure that coplanar polygons are rendered properly by adding the bias (from the DepthBias member of D3D11_RASTERIZER_DESC1) to the z-values that the system uses when rendering the sets of coplanar polygons. Polygons with a larger z value will be drawn in front of polygons with a smaller z value.

There are two options for calculating depth bias.

  1. If the depth buffer currently bound to the output-merger stage has a UNORM format or no depth buffer is bound, the bias value is calculated like this:
    
    
    Bias = (float)DepthBias * r + SlopeScaledDepthBias * MaxDepthSlope;
    
    
    
    where r is the minimum representable value > 0 in the depth-buffer format converted to float32. The DepthBias and SlopeScaledDepthBias values are D3D11_RASTERIZER_DESC1 structure members. The MaxDepthSlope value is the maximum of the horizontal and vertical slopes of the depth value at the pixel.
  2. If a floating-point depth buffer is bound to the output-merger stage the bias value is calculated like this:
    
    
    Bias = (float)DepthBias * 2**(exponent(max z in primitive) - r) +
                SlopeScaledDepthBias * MaxDepthSlope;
    
    
    
    where r is the number of mantissa bits in the floating point representation (excluding the hidden bit); for example, 23 for float32.

The bias value is then clamped like this:



if(DepthBiasClamp > 0)
    Bias = min(DepthBiasClamp, Bias)
else if(DepthBiasClamp < 0)
    Bias = max(DepthBiasClamp, Bias)


The bias value is then used to calculate the pixel depth.



if ( (DepthBias != 0) || (SlopeScaledDepthBias != 0) )
    z = z + Bias


Depth-bias operations occur on vertices after clipping, therefore, depth-bias has no effect on geometric clipping. The bias value is constant for a given primitive and is added to the z value for each vertex before interpolator setup. When you use feature levels 10.0 and higher, all bias calculations are performed using 32-bit floating-point arithmetic. Bias is not applied to any point or line primitives, except for lines drawn in wireframe mode.

One of the artifacts with shadow buffer based shadows is shadow acne, or a surface shadowing itself due to minor differences between the depth computation in a shader, and the depth of the same surface in the shadow buffer. One way to alleviate this is to use DepthBias and SlopeScaledDepthBias when rendering a shadow buffer. The idea is to push surfaces out enough while rendering a shadow buffer so that the comparison result (between the shadow buffer z and the shader z) is consistent across the surface, and avoid local self-shadowing.

However, using DepthBias and SlopeScaledDepthBias can introduce new rendering problems when a polygon viewed at an extremely sharp angle causes the bias equation to generate a very large z value. This in effect pushes the polygon extremely far away from the original surface in the shadow map. One way to help alleviate this particular problem is to use DepthBiasClamp, which provides an upper bound (positive or negative) on the magnitude of the z bias calculated.

Note  For feature levels 9.1, 9.2, 9.3, DepthBiasClamp is not supported.

Related topics

Output-Merger Stage

 

 

Community Additions

ADD
Show:
© 2014 Microsoft