Specifies the beginning and the ending of a set of changes so that System Restore can create a restore point.
For a scriptable equivalent, see CreateRestorePoint.
BOOL SRSetRestorePoint( _In_ PRESTOREPOINTINFO pRestorePtSpec, _Out_ PSTATEMGRSTATUS pSMgrStatus );
- pRestorePtSpec [in]
A pointer to a RESTOREPOINTINFO structure that specifies the restore point.
- pSMgrStatus [out]
A pointer to a STATEMGRSTATUS structure that receives the status information.
If the function succeeds, the return value is TRUE. The llSequenceNumber member of pSMgrStatus receives the sequence number of the restore point.
If the function fails, the return value is FALSE. The nStatus member of pSMgrStatus receives error information.
You must initialize COM security to allow NetworkService, LocalService and System to call back into any process that uses SRSetRestorePoint. This is necessary for SRSetRestorePoint to operate properly. For information on setting up the COM calls to CoInitializeEx and CoInitializeSecurity, see Using System Restore.
This function cannot be called in safe mode. It also fails if System Restore has been disabled (see Disable).
When you call this function, System Restore takes a full snapshot of the registry and other system databases.
Create restore points just prior to a system change, by calling SRSetRestorePoint with the dwEventType member of the RESTOREPOINTINFO structure set to BEGIN_SYSTEM_CHANGE. After the changes to the system have been completed, call SRSetRestorePoint with dwEventType set to END_SYSTEM_CHANGE.
If the user cancels the application installation, the installer may remove the restore point it created when the installation began. Removing the restore point is optional and can prevent the user from recovering from unintentional changes made by the installer during the cancellation. If the installer is to remove a restore point, it can call the SRRemoveRestorePoint function, or call SRSetRestorePoint with dwRestorePointType set to CANCELLED_OPERATION, dwEventType set to END_SYSTEM_CHANGE, and llSequenceNumber set to the value returned by the initial call to SRSetRestorePoint.
Be careful when making nested calls to SRSetRestorePoint. For more information, see Nested calls to SRSetRestorePoint.
A new registry key enables application developers to change the frequency of restore-point creation.
Applications should create this key to use it because it will not preexist in the system. The following applies by default if the key does not exist. If an application calls the SRSetRestorePoint function to create a restore point, Windows skips creating this new restore point if any restore points have been created in the last 24 hours. System Restore sets the IISequenceNumber member of the STATEMGRSTATUS structure to the sequence number for the restore point created previously in the day and sets the value of the nStatus member to ERROR_SUCCESS. The SRSetRestorePoint function returns TRUE.
Developers can write applications that create the DWORD value SystemRestorePointCreationFrequency under the registry key HKLM\Software\Microsoft\Windows NT\CurrentVersion\SystemRestore. The value of this registry key can change the frequency of restore point creation.
If the application calls SRSetRestorePoint to create a restore point, and the registry key value is 0, system restore does not skip creating the new restore point.
If the application calls SRSetRestorePoint to create a restore point, and the registry key value is the integer N, system restore skips creating a new restore point if any restore points were created in the previous N minutes.
System Restore running on Windows 8 monitors files in the boot volume that are relevant for system restore only. Snapshots of the boot volume created by System Restore running on Windows 8 may be deleted if the snapshot is subsequently exposed by an earlier version of Windows. Note that although there is only one system volume, there is one boot volume for each operating system in a multi-boot system.
Developers can write applications that create the DWORD value ScopeSnapshots under the registry key HKLM\Software\Microsoft\Windows NT\CurrentVersion\SystemRestore. If this registry key value is 0, System Restore creates snapshots of the boot volume in the same way as in earlier versions of Windows. If this value is deleted, System Restore running on Windows 8 resumes creating snapshots that monitor files in the boot volume that are relevant for system restore only.
For an example, see Using System Restore.
Minimum supported client
|Windows XP [desktop apps only]|
Minimum supported server
|None supported [desktop apps only]|
Unicode and ANSI names
|SRSetRestorePointW (Unicode) and SRSetRestorePointA (ANSI)|
Build date: 11/6/2012